Vacuums & Floor Care

How to Clean a BISSELL CleanView Swivel Pet 2252

The BISSELL CleanView Swivel Pet 2252 is a bagless upright with a bottom-empty dirt tank, removable cyclone, washable carbon and foam pre-motor filters, a hose path and a belt-driven brush roll beneath a six-screw cover. BISSELL's model-specific support says the filters and cyclone may be washed in warm water with mild dish soap, then air-dried completely for 24 to 48 hours. The brush-roll area is dry maintenance, and the powered vacuum must stay unplugged. Model 2252 appears beside related Swivel variants in support pages, so verify the white model-number label before using screw counts, filter order or replacement parts.

Published · Updated

Primary reference: BISSELL official model 2252 filter and maintenance support. Always check the manual for your exact model.

Quick reference

Washable parts
Foam filter, carbon filter and cyclone: warm water plus mild dish soap.
Drying
Air-dry washed parts completely for 24–48 hours before reinstallation.
Filter order
Thin carbon filter first, thicker foam filter second in the tank lid.
Brush area
Unplug, remove six #2 Phillips screws, clear wraps and inspect roller and belt dry.
Avoid
Wet motor body, damp filters, oiled end caps, metal hose probes and operation without filters.

What you will need

  • A #2 Phillips screwdriver
  • Scissors or a seam ripper with blunt tips
  • A trash can
  • Warm water and mild dish soap
  • Soft cloths and a soft nylon brush
  • A ventilated area for 24–48 hours of filter drying
  • A dry flexible cleaning tool for user-accessible hose clogs
  • Genuine model-compatible filters, belt or brush roll when replacement is needed

Step-by-step instructions

Step 1: Unplug and confirm model 2252

Turn the CleanView off and unplug it. Read the model label because Swivel Pet versions differ in filter and foot construction. Move the machine to a hard floor or protective sheet. Never service the brush roll, belt or hose while connected to power, and do not test suction until every wet part has dried and been reinstalled.

Step 2: Empty the dirt tank at the fill line

Press the tank release, lift the tank away and hold it low over trash. Open the bottom latch and let debris fall without reaching inside near sharp objects. Wipe the door seal and rim. BISSELL notes that a full tank can reduce suction, so do not compact debris above the marked line.

Step 3: Remove the filters and cyclone in order

Open the top filter lid and lift out the thicker foam and thinner carbon filters, noting that BISSELL directs the carbon filter to go back first and foam second. Open the tank bottom, reach the cyclone and twist it left to remove. Photograph the orientation if needed. Do not lose seals or pry parts with a screwdriver.

Step 4: Wash the approved filters and cyclone

BISSELL's 2252 support permits washing the foam and carbon filters and cyclone in warm water with mild dish soap. Gently squeeze filters without wringing or tearing them, rinse until water and foam run clear and rinse the cyclone channels. Wipe the tank with compatible mild solution as needed. Keep water away from the vacuum body and motor.

Step 5: Air-dry for 24 to 48 hours

Set filters, cyclone and washed tank parts in a ventilated place for the full 24–48-hour period BISSELL specifies, longer in humid conditions. Turn parts so hidden water drains. Do not use the vacuum without filters or reinstall them while cool-damp; moisture can restrict suction, cause musty odor and carry dirt toward the motor. Avoid dryers, ovens and hair dryers.

Step 6: Remove the brush roll and inspect the belt

With the vacuum unplugged, recline and turn it over. BISSELL's model support describes removing six #2 Phillips screws, lifting the brush cover and pulling out the brush roll while managing the belt. Note screw positions. Cut wrapped hair along the roller channel without cutting bristles or belt. Keep liquid away from the foot and motor shaft.

Step 7: Check roller end caps and belt condition

Hold the roller by an end cap and spin it. BISSELL advises replacement if it does not spin freely or an end cap is seized. Inspect the belt for cracks, stretching or missing material and replace a damaged belt. Do not oil the end caps, wash the roller assembly or stretch an old belt back into service.

Step 8: Clear the hose and air path

Detach the user-removable hose ends and look through the hose toward light. Remove reachable dry clogs with a flexible blunt tool, working from the nearest opening. Do not use water in the hose unless the exact manual approves washing and provides a complete drying method. Never use metal wire that can puncture corrugations or reach the motor.

Step 9: Reassemble and test

Fit the belt and roller, seat both ends, reinstall the cover and all six screws without overtightening. Once dry, lock the cyclone clockwise, insert carbon then foam filter, click the lids and mount the tank bottom-first. Turn the roller by hand to confirm free movement, then test briefly. Stop for burning-rubber smell, abnormal noise or low suction and recheck assembly.

Specific cleaning questions

Open a question for a concise answer about stains, odors, safety, frequency, and troubleshooting.

Are CleanView Swivel Pet 2252 filters washable?
Yes. BISSELL says the carbon and foam filters can be washed in warm water with mild dish soap, rinsed and air-dried completely for 24–48 hours.
Which filter goes in first?
BISSELL directs the thin carbon filter into the tank lid first, followed by the thicker foam filter. Verify both are fully dry.
Can I wash the cyclone?
Yes. Remove it by twisting left, wash with warm water and mild dish soap, rinse and allow 24–48 hours of complete air drying.
How do I clean hair from the brush roll?
Unplug, remove the six-screw foot cover, lift the roller and belt, and cut wraps carefully without damaging bristles, belt or end caps.
Can I wash the brush roll with water?
Treat it as dry maintenance. Remove hair and debris and inspect the end caps; do not wash the belt-driven roller or powered foot unless BISSELL explicitly says to.
Why does the vacuum smell musty?
Filters may have been installed damp or moist debris may remain. Rewash approved parts and air-dry them fully, and empty the tank after picking up accidental damp material.
When should I replace the brush roll or belt?
Replace the roller if it does not spin freely or an end cap is seized, and replace any belt that is cracked, stretched, broken or otherwise damaged.
Why is suction still low after filter cleaning?
Check complete filter dryness and seating, tank and cyclone assembly, fill level, hose clogs and lower air path. Contact BISSELL if a clean correctly assembled machine remains weak.