Kitchen & Appliances

How to Clean a Bosch Dishwasher Filter

Bosch dishwashers use a removable filter assembly at the bottom of the tub to catch food before it reaches the drain system. A dirty filter can contribute to odor, residue, poor cleaning, standing water, or an E24 drainage symptom, but removal details vary by model. Bosch's general sequence is to remove the lower rack and lower spray arm where required, twist and lift out the filter with its mesh screen, separate the pieces, wash them under running water with mild soap and a soft brush, and lock everything back into place. Cleaning the filter is routine maintenance; reaching beneath its pump cover is a separate troubleshooting task.

Primary reference: Bosch: official dishwasher-filter cleaning instructions. Always check the manual for your exact model.

Quick reference

Access
Cool and stop the dishwasher, then remove lower rack and model-required spray arm.
Unlock
Rotate filter left, lift it with the screen, and separate only designed pieces.
Wash
Use running water, mild soap, and a soft brush on mesh and cylinder.
Reinstall
Seat flat, rotate to locked marker, reinstall arm, and verify free rotation.
Frequency
Clean every few months or sooner for odor, debris, or poor drainage.

What you will need

  • The owner manual for the exact Bosch dishwasher
  • Protective towel for the floor
  • Mild liquid dish soap
  • Warm running water
  • A soft nylon brush or toothbrush
  • A nonabrasive sponge
  • A shallow bowl for loose debris
  • Dry cloths
  • A wooden toothpick for removed spray-arm holes
  • A flashlight for checking the tub sump

Step-by-step instructions

Step 1: Stop the dishwasher and verify the model

Wait until the machine is cool, cancel any active cycle, and switch it off. Check the manual for filter and spray-arm removal because Bosch rack and locking designs differ. Do not work in hot water at the bottom of a recently completed sanitize cycle.

Step 2: Remove the lower rack

Slide the bottom rack completely out and set it on a towel. Remove utensils or broken dish fragments first. The filter is centered in the floor of the tub. Use a flashlight to spot glass or sharp debris without placing bare fingers into standing water or the sump.

Step 3: Remove the lower spray arm when required

Lift, unlock, or release the lower spray arm exactly as the manual shows. Bosch's general filter video includes spray-arm removal. Keep the arm level so debris does not fall back into the tub. Do not pry the hub or bend nozzles.

Step 4: Unlock the filter assembly

Turn the filter knob to the left and lift the cylindrical assembly with its mesh screen. Note its locked and unlocked indicators. Separate the filter from the screen only as designed. Do not force a filter packed with food; loosen visible residue around its edge first.

Step 5: Remove loose food safely

Empty food particles into trash or compost rather than the sink. Inspect the tub opening for labels, bones, glass, and fragments. Use a utensil or protected method for sharp material. Do not remove the pump cover unless the exact Bosch pump-cleaning procedure calls for it.

Step 6: Wash filter pieces

Bosch directs owners to wash the filter under running water with mild soap and a soft brush. Clean inside the cylinder, mesh pleats, screen edges, and locking surfaces. Hold fine mesh against light to find blocked sections. Avoid wire brushes, abrasive pads, bleach, and bending the screen.

Step 7: Inspect and rinse the spray arm

Rinse the removed spray arm with warm water. Bosch says a toothpick can clear buildup from spray holes while the arm is out. Work from the opening without enlarging nozzles, then flush loosened debris out of the arm instead of pushing it deeper.

Step 8: Reinstall and lock

Return the screen and filter in their proper nested position. Turn the filter clockwise to the locked indicator and verify it sits flat without wobble. Reinstall the spray arm and rotate it by hand to confirm free movement, then return the lower rack.

Step 9: Run and monitor a short cycle

Run the dishwasher empty or as the manual recommends and check for normal draining and spray-arm movement. A recurring E24 code, standing water, leak, damaged mesh, or filter that will not lock requires further model-specific diagnosis. Clean the filter every few months or sooner when heavy debris accumulates.

Specific cleaning questions

Open a question for a concise answer about stains, odors, safety, frequency, and troubleshooting.

How often should I clean a Bosch dishwasher filter?
Bosch recommends every few months for normal use. Check sooner with heavy food soil, odor, residue, standing water, or reduced cleaning performance.
Which direction unlocks a Bosch filter?
Bosch's common design rotates left to unlock and lifts out, then rotates right to lock. Confirm arrows and the exact model manual before forcing it.
Can I put the Bosch filter in the dishwasher?
The official method is running water, mild soap, and a soft brush. Hand cleaning lets you inspect fine mesh and locking surfaces closely.
Do I have to remove the lower spray arm?
Many Bosch procedures do, but model designs differ. Follow the owner manual so the arm hub is released rather than pried or bent.
Can a dirty filter cause an E24 code?
A blocked filter can contribute to drainage problems associated with E24, but hoses, pump obstructions, or installation issues can also be responsible. Clean the filter before following further diagnostics.
How do I clean Bosch spray-arm holes?
Remove the arm as directed, rinse with warm water, and use a wooden toothpick to clear individual holes without enlarging them. Flush debris out before reinstalling.
What if I find glass under the filter?
Keep hands out of the sump, disconnect power as the model instructions require, and remove sharp pieces with a protected tool. Pump-cover access is a separate Bosch procedure.
Why does the filter keep coming loose?
It may not be fully rotated to the locked marker, the screen may be misseated, or locking tabs may be damaged. Reinstall carefully and replace a damaged assembly.