How to Clean Golf Pride Grips
Golf grips accumulate sunscreen, skin oil, sweat and dust that can make a club feel slick before the grip is actually worn out. Golf Pride recommends cleaning between rounds with soap, water and a soft brush and also keeping hands and towels clean to slow buildup. Rubber, corded and hybrid grips have different textures, but none benefits from solvent, abrasive sanding, oily conditioner or heat. This guide focuses on the grip surface only, leaving club heads and shafts to their own material-specific care.
Published · Updated
Primary reference: Golf Pride official grip care guide. Always check the manual for your exact model.
Quick reference
- Schedule
- Clean between rounds and after heavy contamination.
- Method
- Mild soap, water and a soft nylon brush.
- Rinse
- Remove every trace of soap from rubber or cord.
- Avoid
- Solvent, alcohol, abrasives, sanding, dressing and heat.
- Replace when
- Clean grip stays hard, glazed, cracked or loose.
What you will need
- Golf Pride's current grip-care guidance
- Warm water
- Small amount of mild dish soap
- Soft nylon brush
- Clean sponge or cloth
- Clean rinse cloth
- Dry towel
- Clean hands for the final traction check
Step-by-step instructions
Step 1: Identify the grip material and condition
Confirm whether the grip is rubber, corded, hybrid or another Golf Pride construction. Look for cracks, glazing, hardening, worn texture, loose ends or movement on the shaft. Cleaning can remove contamination, but it cannot restore rubber that has aged smooth or a grip that twists independently of the club.
Step 2: Protect the club and work area
Place the club where the head cannot fall or strike a hard surface. Keep the grip end lower than vulnerable shaft labels or use controlled cloth moisture so wash water does not run along the shaft. Do not soak the entire club or let water enter an open butt end.
Step 3: Remove loose dust
Wipe dry dust and sand from the grip with a clean cloth. On corded sections, use a dry soft brush in the texture's direction. This first pass prevents grit from scratching finish at the grip collar or being ground deeper into rubber during the soap step.
Step 4: Apply mild soap and water
Wet a cloth or sponge with warm water and a small amount of mild dish soap. Work the lather around the grip from cap to lower edge. Golf Pride recommends soap and water rather than solvent or dressing. Use modest moisture and support the shaft so scrubbing does not twist the grip.
Step 5: Brush the texture gently
Use a soft nylon brush to lift oil and dirt from grooves, rubber patterns and cord. Work all sides evenly and avoid aggressive pressure at logos or boundaries between materials. Do not use a wire brush, sandpaper or magic eraser; changing the designed texture can shorten life and produce uneven grip.
Step 6: Rinse off all soap
Use a clean damp cloth or controlled low-flow rinse while keeping water from traveling down the shaft. Repeat until there is no foam and the surface no longer feels slick. Soap left in cord or deep texture can attract new dirt and reduce traction during the next round.
Step 7: Towel and air-dry
Squeeze the grip only with the towel's gentle pressure and wipe from end to end. Let it air-dry at room temperature. Do not use a hair dryer, radiator or direct intense sun. Heat can harden rubber and weaken adhesive at the grip-to-shaft interface.
Step 8: Test with clean dry hands
When fully dry, hold the grip as you would at address and make a low-speed practice motion in a safe area. The surface should feel secure without tacky product. If it remains slick, repeat the rinse once to exclude soap residue; a clean grip that remains hard or glossy is likely worn.
Step 9: Reduce future buildup
Golf Pride recommends cleaning between rounds and keeping hands clean. Use water and a clean towel to remove sunscreen, food oil or soil from hands during play, and rotate towels before they become greasy. Store clubs dry and out of extreme vehicle heat, which can age grips even when they look clean.
Specific cleaning questions
Open a question for a concise answer about stains, odors, safety, frequency, and troubleshooting.