Vacuums & Floor Care

How to Clean a Roborock Saros 10R Robot Vacuum and Dock

The Roborock Saros 10R combines a DuoDivide main brush, side brush, detachable mop components, navigation sensors, and a multifunction dock that washes and dries the mops. Automatic maintenance reduces daily handling but does not remove hair from brush ends, clean the robot's filter, wipe sensors, or empty and rinse dock tanks for you. Exact app reminders and part intervals can change with use, so use the Saros 10R manual and Roborock app as the final schedule.

Published · Updated

Primary reference: Roborock official Saros 10R user manual. Always check the manual for your exact model.

Quick reference

Robot safety
End the task, power off, and place the robot on a soft dry surface before removing parts.
Hair points
Clean the DuoDivide rollers, end caps, side brush, caster, and main-wheel axles.
Dock hygiene
Empty dirty water promptly and clean tanks, filter screens, and removable wash components.
Sensors
Wipe sensor windows and charging contacts with a clean dry microfiber cloth.
Avoid
Unapproved detergent, wet electronics, reused dust bags, forced brush covers, and false reminder resets.

What you will need

  • The official Saros 10R manual and Roborock app maintenance screen
  • A trash container
  • Clean dry microfiber cloths
  • A soft cleaning brush
  • Cold or lukewarm water for approved washable parts
  • Blunt scissors for accessible wrapped hair
  • A ventilated drying area away from direct heat

Step-by-step instructions

Step 1: End the task and power down safely

Pause cleaning, return the robot to an accessible area, and turn it off through the prescribed control before removing brushes or the dustbin. Unplug the multifunction dock before wiping its contacts, tray area, or exterior. Do not invert the robot with liquid remaining on mop cloths, and keep water away from the robot body, sensor windows, charging contacts, dock cord, and power socket.

Step 2: Empty the robot dustbin

Lift the robot cover, release the dustbin, and empty it over trash without striking it against a hard surface. Remove the filter through its frame and tap off loose dust. If the Saros 10R manual marks the dustbin or filter as washable, rinse with clean water only; never reinstall either while damp. A dock dust bag is disposable and must be replaced rather than emptied or washed.

Step 3: Clean the DuoDivide main brush

Turn the powered-down robot over on a soft dry surface. Release the main-brush cover and remove the DuoDivide brush components in the manual's order. Pull hair and threads from the split rollers, their ends, and the intake, using blunt scissors only where needed. Confirm end caps move freely, then reinstall the correct side of each component and lock the cover flat.

Step 4: Service the side brush and wheels

Remove tangled hair from the FlexiArm side brush without stretching or bending its arms. Follow the manual if the fastener must be removed. Rotate the main wheels and front caster by hand to expose fibers around the axles, then lift debris with a dry brush. Do not add oil or flood a wheel opening; a wheel that remains stiff may require service.

Step 5: Clean the mop cloths and mounts

Detach the mop cloths or mop modules only as shown for the Saros 10R. Rinse approved cloths with water and clean away grit that the dock wash did not remove, then dry them fully before storage or extended idle time. Wipe the mounts and attachment faces. Do not use bleach, fabric softener, or an unapproved cleaner that can leave residue on floors or interfere with the dock.

Step 6: Wipe sensors and charging contacts

Use a clean dry microfiber cloth on the navigation sensor windows, wall sensor, cliff sensors, carpet sensor, dock locator, and charging contacts identified in the manual. Wipe rather than spray. Do not use abrasive pads, alcohol unless explicitly approved, or a wet swab inside a sensor opening. Clean contacts on both robot and dock so automatic charging and maintenance can complete reliably.

Step 7: Empty and rinse the dock tanks

Remove the dirty-water tank promptly, discard its contents, rinse the tank and lid with clean water, and wipe the seal. Refill the clean-water tank to its marked level using water and only Roborock-approved solution in the specified system and ratio. Never pour cleaner directly into an unapproved compartment, swap tank positions, or leave dirty water standing long enough to create odor.

Step 8: Clean the dock wash area

Use the dock's cleaning or tray-release procedure from the Saros 10R manual. Remove hair, sludge, and grit from the removable wash components, water outlet area, and filter screen without pushing debris into a drain. Rinse only detachable parts listed as washable and dry or reseat them correctly. Keep the powered dock housing and hot-water system out of the sink.

Step 9: Reset only completed maintenance reminders

Reinstall a fully dry robot filter and dustbin, lock the brushes and mop pieces, return the tanks and tray, and reconnect the dock. Run a short cleaning and docking test while watching for leaks or unusual brush noise. In the Roborock app, reset a maintenance counter only after that component was actually cleaned or replaced; the counter is a reminder, not a condition sensor.

Specific cleaning questions

Open a question for a concise answer about stains, odors, safety, frequency, and troubleshooting.

Does the Saros 10R dock clean everything automatically?
No. It can empty dust and wash or dry mops, but brushes, axles, robot filters, sensors, contacts, tanks, and the dock wash area still need manual maintenance.
Can I wash the Roborock Saros 10R filter?
Wash it only if the Saros 10R manual identifies that exact filter as washable. Use clean water without detergent and reinstall it only after it is dry throughout.
How do I clean the Saros 10R DuoDivide brush?
Power off the robot, release the brush cover, remove the split brush components, clear hair from rollers and ends, and lock every piece back in its original orientation.
Can I put floor cleaner in the Saros 10R water tank?
Use only a Roborock-approved solution and only in the compartment and dilution specified for the exact dock. Other cleaners can foam, clog passages, or leave residue.
Why does the Saros 10R dock smell?
Dirty water, a damp dock filter or tray, soiled mop cloths, or trapped sludge can cause odor. Empty dirty water promptly and clean and dry the removable wash components.
Can I spray cleaner on Saros 10R sensors?
No. Use a clean dry microfiber cloth and keep liquids out of sensor openings. Spraying can leave a film or move moisture behind a window.
How often should I replace the dock dust bag?
Use the dock or app indication and inspect for fullness, odor, or damage. Replace the disposable bag; do not empty, rinse, or reuse it.
Why should I not reset all maintenance counters at once?
The counters estimate use. Resetting an item that was not serviced removes a useful reminder and can let a loaded filter or worn brush remain in service longer.